50μm 3003 H14 Aluminum Foil

☆☆☆☆☆
(0 customer reviews)

These characteristics make it suitable for applications where very thin foil may lack sufficient mechanical stability, while thicker aluminum sheet would add unnecessary weight or material cost. Available with alloy 3003.

1. Introduction to 50μm 3003 H14 Aluminum Foil

50μm 3003 H14 aluminum foil is a medium-gauge aluminum foil manufactured from 3003 aluminum alloy and supplied in the H14 temper.

With a nominal thickness of 0.05 mm, it combines the lightweight characteristics of aluminum foil with the higher strength and practical forming performance associated with the 3003 alloy.

The material offers a useful balance between strength, corrosion resistance, formability, thermal performance, and barrier properties.

These characteristics make it suitable for applications where very thin foil may lack sufficient mechanical stability, while thicker aluminum sheet would add unnecessary weight or material cost.

The designation itself contains three important pieces of information:

3003 – identifies the aluminum-manganese alloy.

H14 – identifies the work-hardened temper.

50μm – specifies the nominal foil thickness.

This combination is particularly relevant for industrial buyers because alloy, temper, and thickness directly influence processing behavior.

A 50μm foil with a softer temper will not behave exactly like 50μm H14 foil, even when both use the same 3003 alloy.

50m-3003-H14-Aluminum-Foil

2. What Is 3003 Aluminum Foil?

3003 aluminum foil is a rolled aluminum foil manufactured from AA 3003 aluminum alloy, a non-heat-treatable alloy within the 3xxx aluminum series.

The main alloying element responsible for its characteristic performance is manganese. Compared with commercially pure aluminum grades, 3003 provides higher mechanical strength while retaining good corrosion resistance and useful formability.

This makes 3003 particularly suitable when an application requires more structural stability than soft pure-aluminum foil can provide.

2.1 Chemical Composition of 3003 Aluminum Foil

The chemical composition of 3003 aluminum alloy is primarily based on aluminum with manganese as the principal alloying element.

The following table summarizes the commonly specified composition ranges and maximum limits used for 3003 aluminum alloy.

Exact requirements should follow the applicable ASTM, EN, or customer specification.

Element Chemical Composition (wt.%) Function / Effect
Al Balance Base metal; provides low density, corrosion resistance, and thermal conductivity
Mn 1.0–1.5 Main alloying element; increases strength and improves corrosion resistance
Cu 0.05–0.20 Provides a moderate increase in strength
Fe ≤ 0.70 Controlled impurity; influences strength and microstructure
Si ≤ 0.60 Controlled impurity; affects strength and processing behavior
Zn ≤ 0.10 Minor element; maintained at a low level to control alloy performance
Other Elements ≤ 0.05 each; ≤ 0.15 total Controlled to maintain alloy consistency
Total Alloying & Impurity Elements Within applicable standard limits Ensures consistent processing and finished-product properties

3. Understanding the H14 Temper

The H14 temper is one of the most important characteristics of this product because it determines how the 3003 alloy responds mechanically during processing.

Unlike heat-treatable aluminum alloys, 3003 develops its H14 condition primarily through strain hardening or cold working.

The basic principle is straightforward:

Cold deformation increases the strength of the aluminum while reducing some of its ductility.

As the material passes through rolling operations, its crystal structure becomes increasingly resistant to further plastic deformation.

This produces higher strength compared with the annealed O condition.

3.1 What Does H14 Mean?

The letter H identifies a strain-hardened aluminum temper.

The first digit after H indicates the type of strain-hardening treatment, while the second digit indicates the degree of hardening.

For H14:

H = strain-hardened

1 = strain-hardened only

4 = commonly associated with a half-hard level

Therefore, 3003-H14 represents a strain-hardened 3003 alloy rather than a heat-treated alloy.

ASTM's aluminum product standards recognize alloy and temper designations within their specifications, and ASTM documentation specifically discusses H14 and related H1x/H2x temper relationships.

3.2 H14 vs. O Temper

The most useful comparison is often between 3003 H14 and 3003 O.

3003 O has undergone annealing and therefore offers greater ductility and easier forming. H14, by contrast, has higher strength and better resistance to deformation.

This creates a practical trade-off:

Characteristic 3003 O 3003 H14
Strength Lower Higher
Ductility Higher Moderate
Formability Excellent Good
Shape retention Lower Better
Resistance to deformation Lower Higher
Typical use Deep forming General industrial processing

The appropriate temper depends on the forming depth, bending requirements, tension during converting, and final product design.

3.3 Why H14 Matters at 50μm

At only 0.05 mm, aluminum foil has limited structural rigidity simply because of its small cross-sectional thickness.

The H14 temper helps compensate for this limitation by increasing the material's mechanical strength.

However, increased strength also means that H14 is less ductile than a fully annealed O temper.

Therefore, manufacturers and converters should match the temper to the forming and converting requirements rather than selecting H14 solely because it has higher strength.

Food-Packaging-Used-50m-3003-H14-Aluminum-Foil

4. Why Choose 50μm Thickness?

A thickness of 50μm, or 0.05 mm, occupies an important position between ultra-thin aluminum foil and thicker foil or sheet products.

The main reason to choose this gauge is its ability to provide a practical combination of material efficiency and mechanical stability.

4.1 Balance Between Weight and Strength

Reducing foil thickness can lower material consumption, weight, and potentially product cost.

At 50μm, the foil retains the lightweight characteristics expected from aluminum foil while providing more material thickness than many ultra-thin foil products.

This makes it attractive for applications where extremely thin foil is not necessary but conventional sheet material would be unnecessarily heavy.

4.2 Barrier Performance

Aluminum provides an effective barrier against light, moisture, and gases when the foil remains continuous and defect-free.

Therefore, 50μm should not be interpreted as a universal barrier-performance specification. For demanding applications, manufacturers should evaluate the complete structure and applicable test requirements.

4.3 Processing Advantages

50μm aluminum foil can provide a useful balance for converting processes such as:

Slitting

Laminating

Coating

Printing

Forming

Composite production

The H14 temper can further improve dimensional stability during these processes.

The 50μm H14 combination therefore offers a middle-ground solution between flexibility and mechanical stability.

4.4 Material Efficiency

Thickness also directly affects material consumption.

For the same width and length, 50μm foil contains less aluminum than thicker products.

This can reduce the weight of the final product and make it suitable for lightweight construction.

At the same time, the 50μm gauge remains substantial enough for applications requiring better handling characteristics than very thin foil.

5. Key Properties of 50μm 3003 H14 Aluminum Foil

The performance of 50μm 3003 H14 aluminum foil results from the interaction of alloy composition, temper, thickness, rolling quality, and surface condition.

5.1 Mechanical Properties

The H14 temper gives 3003 foil higher strength than its annealed counterpart.

Key mechanical parameters include:

Tensile strength

Yield strength

Elongation

Hardness

For procurement, buyers should use the mechanical-property limits specified by the applicable standard and product thickness rather than relying on generic values found in product catalogs.

ASTM specifications establish mechanical-property requirements for applicable aluminum products and describe how tensile strength, yield strength, and elongation are evaluated.

5.2 Good Formability

Although H14 increases strength, 3003 retains useful ductility.

This makes the material suitable for moderate forming, bending, shaping, and converting operations.

For deep drawing or highly complex forming, however, a softer temper such as O may be more appropriate.

The key is to match the foil temper to the actual deformation required by the finished product.

5.3 Corrosion Resistance

3003 aluminum generally offers good atmospheric corrosion resistance.

Its aluminum-rich surface naturally develops a thin oxide layer that helps protect the underlying metal from further oxidation.

This property is useful in environments involving:

Humidity

Atmospheric exposure

Thermal systems

Packaging structures

General industrial applications

Actual corrosion performance depends on the environment and the presence of other materials or chemicals.

5.4 Thermal Conductivity

Aluminum provides good thermal conductivity, which makes 3003 foil useful in thermal management and heat-transfer-related applications.

At 50μm, the foil can provide a lightweight thermal-conductive layer in composite or laminated structures.

However, when maximum electrical or thermal conductivity is the primary requirement, commercially pure aluminum may offer advantages over alloyed grades such as 3003.

5.5 Barrier Properties

A continuous aluminum foil layer provides strong protection against light and can serve as a barrier against moisture and gases.

The effectiveness of the final barrier depends heavily on foil integrity.

For this reason, pinholes and microscopic defects are critical quality-control factors for thin-gauge foil.

5.6 Surface Quality

For downstream processing, surface quality can be as important as mechanical properties.

A high-quality 50μm foil should maintain a controlled surface condition with minimal:

Scratches

Stains

Oil residues

Wrinkles

Roll marks

Edge cracks

Other visible defects

Surface requirements should be agreed upon before production, especially when the foil will undergo printing, coating, or lamination.

Huawei-3003-Aluminum-Foil-Slitting

6. Manufacturing Process of 50μm 3003 H14 Aluminum Foil

Producing 50μm 3003 H14 aluminum foil requires precise control of alloy composition, rolling reduction, thickness, temper, and surface quality throughout the production process.

6.1 Alloy Preparation and Casting

Aluminum and alloying elements are melted according to the required 3003 composition.

The molten metal is chemically analyzed and then cast into suitable slabs or feedstock for rolling.

6.2 Homogenization and Hot Rolling

The cast material may undergo homogenization to improve metallurgical consistency.

Hot rolling then reduces the material thickness and prepares it for subsequent cold rolling.

6.3 Cold Rolling

Cold rolling gradually reduces the aluminum strip to the required gauge.

For 50μm foil, precise control of rolling reduction, tension, flatness, and surface condition is essential to maintain uniform thickness and stable quality.

6.4 Intermediate Annealing

Depending on the rolling schedule, intermediate annealing may restore ductility and allow further thickness reduction.

The process must be carefully controlled to achieve the required final mechanical properties.

6.5 Final Rolling and H14 Temper Control

The final cold-rolling passes bring the foil to the target 50μm thickness while establishing the required H14 temper through controlled work hardening.

6.6 Slitting and Inspection

The finished jumbo coil can be slit into customized widths. Quality inspection typically covers alloy composition, thickness, width, tensile properties, elongation, surface condition, and edge quality.

6.7 Packaging

Finally, the 50μm foil is carefully packed with moisture, edge, and mechanical protection to prevent damage during storage and international transportation.

7. Surface and Processing Options

The surface condition of 50μm 3003 H14 aluminum foil directly affects its appearance, converting performance, adhesion, and suitability for downstream processing.

The required finish should therefore be defined according to the final application.

7.1 Mill Finish

Mill finish is the standard surface condition produced during aluminum rolling.

It provides a practical surface for general industrial applications and can serve as the base for subsequent coating, laminating, or other treatments.

For applications where appearance is important, buyers should specify acceptable surface defects and visual requirements before production.

7.2 Bright and Matte Surface

Depending on rolling conditions and the finishing process, 3003 aluminum foil can be supplied with different surface appearances.

A bright surface provides higher visual reflectivity and is useful when appearance or light reflection matters.

A matte surface offers a less reflective appearance and may be preferred for certain laminated, printed, or industrial products.

Surface requirements should be clearly defined because "bright" and "matte" can represent different commercial requirements between suppliers.

7.3 Slitting and Width Customization

Jumbo 50μm foil coils can be slit into narrower widths according to the customer's equipment and final product dimensions.

For high-speed converting, stable coil winding and clean edges are particularly important.

7.4 Laminating

50μm 3003 H14 aluminum foil can be laminated with materials such as polymer films, paper, or other substrates to create multilayer structures.

The foil surface may require appropriate cleaning or treatment to achieve reliable adhesive bonding.

7.5 Coating and Printing

The foil can also serve as a substrate for protective, functional, or decorative coatings.

Coating and printing requirements should consider surface cleanliness, coating adhesion, curing conditions, and the intended end use.

7.6 Embossing and Forming

Where required, aluminum foil can undergo embossing or forming to create a specific surface pattern or geometry.

However, the H14 temper provides higher strength than soft-temper foil, so the forming depth and deformation level should be evaluated before selecting the material.

Coated-50m-3003-H14-Aluminum-Foil

8. Specifications of 50μm 3003 H14 Aluminum Foil

A technical specification for 50μm 3003 H14 aluminum foil should cover more than nominal thickness.

Buyers normally define the alloy, temper, dimensions, surface condition, mechanical requirements, coil configuration, and applicable standards.

Parameter Specification / Typical Value
Alloy 3003
Temper H14
Nominal Thickness 50 μm / 0.050 mm
Thickness in Inch 0.00197 in.
Density Approx. 2.73 g/cm³
Tensile Strength Approx. 138–179 MPa*
Yield Strength (0.2%) Approx. ≥117 MPa*
Elongation Typically ≥2–4%*
Surface Mill Finish / Bright / Matte
Form Jumbo Coil / Slit Coil
Width Customized
Width Tolerance According to agreed specification
Core ID 76 / 152 / 203 mm or Customized
Coil OD Customized
Coil Weight Customized
Processing Options Slitting / Laminating / Coating / Printing
Applicable Standards ASTM / EN / JIS / Customer Specification

9. Applications of 50μm 3003 H14 Aluminum Foil

The combination of 3003 alloy, H14 temper, and 50μm thickness makes this foil suitable for applications that require a balance of lightweight construction, moderate strength, corrosion resistance, and barrier or thermal functionality.

9.1 Food and Industrial Packaging

Aluminum foil can provide an effective barrier against light, moisture, and gases when the foil layer remains continuous and properly processed.

50μm 3003 H14 foil can therefore be used as a material layer in selected:

Flexible packaging structures

Food packaging components

Lids and covers

Laminated packaging

Heat-resistant packaging structures

For direct food-contact applications, the finished product must comply with the applicable food-contact regulations in the destination market. Alloy selection alone does not establish regulatory compliance.

9.2 Thermal Insulation

Aluminum foil is widely used as a reflective and barrier layer in insulation systems.

50μm foil can be incorporated into multilayer insulation structures where the aluminum layer contributes to:

Radiant heat reflection

Moisture resistance

Vapor barrier performance

Lightweight construction

The actual thermal performance depends on the complete insulation assembly rather than foil thickness alone.

9.3 HVAC and Refrigeration

3003 is widely associated with general-purpose applications and heat-transfer equipment. The Aluminum Association specifically identifies 3003 as a popular alloy for applications including heat exchangers and cooking utensils.

In HVAC and refrigeration-related products, aluminum's corrosion resistance, thermal conductivity, low density, and formability can make it useful in selected foil or laminated components.

The exact alloy and temper should be selected according to the forming, brazing, thermal, and environmental requirements of the specific component.

50m-3003-H14-Aluminum-Foil-for-HVAC

9.4 Laminated Industrial Materials

50μm 3003 H14 foil can function as a metallic barrier layer in composite materials.

Laminating aluminum foil with polymer films, paper, or other substrates can create structures with improved resistance to:

Moisture

Light

Gas transmission

External contamination

This makes aluminum foil useful in various industrial packaging and protective structures.

9.5 Electrical and Electronic Applications

Aluminum provides good electrical and thermal conductivity, low density, and corrosion resistance.

50μm 3003 H14 foil can therefore be considered for selected electrical or electronic components where moderate strength and dimensional stability are more important than maximum electrical conductivity.

Where electrical conductivity is the primary performance requirement, commercially pure aluminum grades may be more appropriate.

10. 50μm 3003 H14 Aluminum Foil vs. Other Aluminum Foils

Property 50μm 3003 H14 3003 O 1050 / 1060 3004 H14
Alloy Series 3xxx 3xxx 1xxx 3xxx
Temper H14 O Commonly O / H14 H14
Nominal Thickness 50 μm Customized Customized Customized
Main Alloying Element Mn Mn Minimal alloying Mn + Mg
Strength Moderate Lower Generally lower Generally higher
Formability Good Excellent Excellent in soft temper Good
Ductility Moderate High High Moderate
Corrosion Resistance Good Good Good Good
Thermal Conductivity Good Good Generally higher Good
Electrical Conductivity Good Good Generally higher Good
Shape Retention Good Lower Lower in soft temper Good
Deep Forming Limited compared with O temper Excellent Excellent in soft temper Good
Processing Stability Good High flexibility but lower strength Depends on temper Good
Typical Applications Industrial foil, insulation, laminated materials, packaging Deep-forming and highly ductile applications Electrical, thermal, packaging, general-purpose foil Higher-strength packaging and industrial applications
Main Selection Consideration Balance of strength, formability, and 50μm material efficiency Maximum ductility and forming ability Purity, conductivity, and ductility Higher strength within 3xxx series

11. 50μm 3003 H14 Aluminum Foil from Henan Huawei Aluminum

11.1 Manufacturer and Supply Capability

Henan Huawei Aluminum Co., Ltd. is an experienced aluminum manufacturer and supplier specializing in aluminum sheet, plate, coil, foil, strip, and circle products.

For 50μm 3003 H14 aluminum foil, Huawei can customize key specifications including alloy, temper, thickness, width, coil dimensions, surface condition, and downstream processing requirements.

The 50μm thickness equals 0.05 mm, providing a practical balance between material efficiency, flexibility, strength, and handling performance.

11.2 Thickness and Surface Quality

For 50μm aluminum foil, thickness consistency is particularly important. Gauge variation can affect roll weight, tension control, lamination, coating, slitting, and downstream forming.

Huawei applies controlled rolling and inspection procedures to maintain consistent foil thickness and surface quality.

Depending on the application, customers can select mill finish, bright, matte, or other suitable surface conditions.

Slitting and other value-added processing can also be arranged according to production requirements.

11.3 Customized 50μm Aluminum Foil

Different applications require different foil configurations. A packaging converter may focus on surface quality and lamination performance, while an industrial user may prioritize coil weight, width, winding quality, and processing stability.

Huawei can customize:

Alloy: 3003

Temper: H14

Thickness: 50μm / 0.05 mm

Width: Customized

Core ID: 76 mm, 152 mm, or customized

Surface: Mill finish, bright, matte, etc.

Coil weight: Customized

Coil OD: Customized

Processing: Slitting, laminating, coating, printing, etc.

Packaging: Customized export packaging

This approach allows buyers to obtain foil that matches their production equipment and processing requirements.

11.4 Quality Control

Quality control for 50μm 3003 H14 aluminum foil covers more than alloy composition.

Dimensional control focuses on thickness, width, coil dimensions, and agreed tolerances.

Mechanical testing can include tensile strength, yield strength, and elongation according to the applicable product specification.

Surface inspection helps identify scratches, rolling marks, oil stains, edge defects, and other surface problems that could affect subsequent processing.

Coil quality also matters. Winding tension, edge condition, telescoping, roll stability, and overall coil appearance can influence slitting, coating, laminating, and automated production.

Huawei can also support inspection documentation and third-party inspection requirements for suitable export orders.

Aluminum-Foil-Jumbo-Roll-Packaged-By-Huawei

12. Factors Affecting the Price of 50μm 3003 H14 Aluminum Foil

The price of 50μm 3003 H14 aluminum foil depends on more than the nominal thickness.

Aluminum market prices, alloy and temper, processing requirements, order quantity, surface condition, packaging, and logistics can all affect the final quotation.

12.1 Aluminum Raw Material Price

The price of primary aluminum represents an important part of the final foil cost.

Changes in international aluminum market prices can therefore influence the quotation for 3003 aluminum foil.

When comparing suppliers, buyers should distinguish between the aluminum material component and the manufacturer's processing cost.

12.2 Alloy and Temper

3003 H14 aluminum foil requires controlled alloy preparation and cold working to achieve the required temper.

Compared with 3003-O foil, H14 material requires additional control over the work-hardening process and final mechanical properties.

Therefore, alloy and temper requirements can influence the final production cost.

12.3 Thickness and Thickness Tolerance

The nominal thickness of this product is 50μm, but the required thickness tolerance also affects production difficulty.

Standard commercial tolerances and tighter customer-specific tolerances may involve different levels of process control and inspection.

For precision applications, buyers should specify the required tolerance when requesting a quotation.

12.4 Width and Slitting Requirements

Width has a direct influence on processing.

A wide jumbo coil may require fewer processing steps, while multiple narrow slit coils require additional slitting, rewinding, edge control, inspection, and packaging.

Therefore, the requested finished width and number of slit rolls can affect the unit price.

12.5 Coil Weight and Packaging

Coil configuration also affects the quotation.

Small slit coils and large industrial coils require different winding, handling, and packaging arrangements.

For export shipments, packaging may include moisture protection, edge protection, pallets, steel straps, and other measures according to transportation requirements.

12.6 Surface Requirements

Standard mill-finish foil generally requires fewer processing steps.

If the customer requires a specific bright or matte surface, coating, lamination, printing, or another value-added process, the additional processing can increase the overall cost.

12.7 Order Quantity

Order quantity can significantly affect the unit price.

Larger orders can distribute production setup, testing, slitting, packaging, and other fixed costs over a greater volume.

Small trial orders may therefore have a higher unit cost than large-volume orders.

12.8 Delivery Terms and Destination

International quotations can vary depending on the selected delivery terms.

Common terms include:

EXW

FOB

CFR

CIF

Freight, insurance, port charges, and destination-related costs can all affect the final landed cost.

12.9 Inspection and Certification Requirements

Some customers require standard mill certificates, while others may require additional inspection reports or third-party inspection.

These requirements can increase procurement costs but may be necessary for specific industrial applications.

13. Conclusion

50μm 3003 H14 aluminum foil combines a relatively thin gauge with the higher strength and improved dimensional stability provided by the H14 temper.

The 3003 aluminum alloy offers good corrosion resistance, useful formability, and balanced mechanical properties.

The H14 temper increases strength compared with the annealed condition while retaining practical flexibility for many processing applications.

At 50μm / 0.05 mm, the foil provides a useful balance between material consumption and handling performance.

It can be used where controlled thickness, moderate strength, flexibility, and corrosion resistance are important.

For long-term procurement, price should not be the only consideration.

Thickness consistency, surface quality, mechanical properties, processing stability, batch consistency, packaging, and delivery reliability can all influence the actual purchasing value of the material.

Henan Huawei Aluminum Co., Ltd. can provide customized 3003 H14 aluminum foil specifications and support different widths, coil configurations, surface conditions, processing requirements, and export packaging solutions.

FAQs

1. What is 50μm 3003 H14 aluminum foil?

It is aluminum foil made from 3003 aluminum alloy in the H14 temper, with a nominal thickness of 50μm (0.05 mm). It offers a practical balance of strength, flexibility, corrosion resistance, and material efficiency.

2. What is the difference between 3003 H14 and 3003 O foil?

3003 H14 has higher strength and better shape retention, while 3003 O offers higher ductility and easier forming. H14 is suitable when moderate strength and dimensional stability are important.

3. Can 50μm 3003 H14 aluminum foil be customized?

Yes. Suppliers can customize width, coil weight, core diameter, surface finish, slitting, packaging, and other specifications according to the customer's production requirements.

4. What surface finishes are available?

Common options include mill finish, bright finish, and matte finish. Lamination, coating, and printing can also be available for suitable applications.

5. What are the main applications?

50μm 3003 H14 aluminum foil can be used for thermal insulation, industrial packaging, HVAC and refrigeration materials, laminated products, and other industrial applications requiring controlled thickness and moderate strength.

6. What factors affect the price?

The main factors include aluminum market price, alloy and temper, thickness tolerance, width, order quantity, slitting, surface treatment, coil specifications, packaging, inspection, and delivery terms.

7. How can I get an accurate quotation?

Provide the supplier with the alloy, temper, thickness, width, surface, coil requirements, quantity, application, and destination. Complete specifications allow the manufacturer to calculate the material and processing costs more accurately.

8. Why choose Henan Huawei Aluminum?

Henan Huawei Aluminum can supply customized 3003 H14 aluminum foil with controlled thickness, surface quality, coil specifications, and processing options. The company also provides technical support and export-oriented supply services for international customers.

Previous Post
Next Post

Get a Quote!

Edit Template

Address

52 Dongming Road, Guancheng District, Zhengzhou City, Henan Province, China. 450000

Call us

Copyright © Henan Huawei Aluminum Co., Ltd. All Rights Reserved.